Construction Chemicals
Floor Applications
Ademix 716 Epoxy Flat
Top Coat Epoxy Floor Coating Material
Top Coat Epoxy Floor Coating Material
It Is An Epoxy Based, Double Component, Solvent-Free, Top Coat Floor Coating Material Applied by Roller.
It is used in concrete and cement screed surfaces, undercoat systems dulled with sand as a topcoat, maintenance workshops, garage, and loading ramps, etc, surfaces exposed to normal, medium and heavy loads and chemicals, multistorey and underground car parks and maintenance hangars, industrial warehouses, beverage and food industry, shopping malls and supermarkets, laboratories, exhibition, and fair areas.
It is easy to apply.
It is solvent-free.
It has high mechanical and chemical resistance.
It has high abrasion strength.
It has a glossy surface finish.
A non-slip surface can be obtained.
It is liquid impermeable.
Epoxy Resin – Color, Liquid (Ral Colors)
Epoxy Hardener – Transparent Liquid
Epoxy Resin (Component A): 21.44 kg tin can
Epoxy Hardener (Component B): 3.56 kg tin can
Component A: ~ 1,60 kg/lt
Component B: ~ 1,0 kg/lt
Mixture: ~ 1,50 kg/lt
Mortar: ~ 50 N/mm² (28 days / +23°C / 50% relative humidity)
Mortar: ~ 20 N/mm² (28 days / +23°C / 50% relative humidity)
> 1.5 N/mm²
: ~ 80 (7 days / +23°C / 50% relative humidity)
<70 mg (CS10, 1000, 1000) (8 days 23°C) (EN ISO 5470-1 Taber)
*The above values were obtained as a result of laboratory experiments.
:
+10°C minimum / +30°C maximum
+10°C minimum / +30°C maximum
Humidity ratio <4% by weight
~ 7 days
80% maximum
+10°C ~ 80 minutes
+20°C ~ 40 minutes
+30°C ~ 20 minutes
*These values are valid for 23°C of temperature and 50% relative humidity. Times may vary depending on ambient conditions.
The concrete surface should be clean, strong and have sufficient compressive strength (minimum 25 N/mm²).
The surface should be clean, dry and free from foreign substances such as dirt, oil, coating, surface curing materials.
Concrete or screed surfaces should be primed or levelled to form a smooth surface.
Component B of ADEMIX 716 EPOXY FLAT should be added into component A and stirred with an aid of 300-400 rpm for 3 minutes until a homogeneous mixture is obtained.
To make sure that the mixture is made completely, the mixture is put in another container and stirred again for another 1 minute.
Over stirring should be avoided to minimize air entrainment.
ADEMIX EPOXY PRIMER 711/712/713 is applied to the floor with the help of an unused rake or roller.
ADEMIX EPOXY PRIMER 711/712/713 products can be used for levelling uneven surfaces.
ADEMIX 716 EPOXY FLAT is applied with a short pile roller.
ADEMIX 716 EPOXY FLAT should be poured on the surface, propagated with rake and traversed with a short pile roller.
ADEMIX 716 EPOXY FLAT For the best results in its application, ambient temperature should be in between +10°C and +30°C
and necessary measures should be taken in bad weather conditions.
-Processability and curing times vary according to the ambient temperature. The times are shorter at high temperatures, and longer at low temperatures.
-The application area should be protected from heavy weather conditions for 24 hours after the application. (sun, wind, frost, rain, etc.)
– The pre-stored packages to be opened for application should be ready for use at an average of 25°C.
-Upon the completion of the application, the coating should not be exposed to water directly for at least 24 hours.
-Used tools and equipment should be cleaned with cellulosic thinner or suitable solvent after application.
-All application areamust be prepared with the same batch number of ADEMIX 714 FLAT for exact color matching.
As a coating; for one coat; approximately 0.25 – 0.3 kg/m²
All necessary Occupational Health and Safety measures must be taken in the application areas. All work safety equipment, such as work clothes, protective gloves/goggles /mask, should be used during the application in accordance with the Occupational Health and Safety rules. Ventilation of the working area is required. Warehouse and stock areas should not be approached with fire. Contact of the product with the skin and eyes should be prevented, in such a case, the contacted part of the skin should be washed with plenty of water and medical attention is required immediately. Food and beverages should also not come into contact with the product. It should be kept out of reach of children.
Epoxy Resin – Color, Liquid (Ral Colors)
Epoxy Hardener – Transparent Liquid
25 kg set
Epoxy Resin (Component A): 21.44 kg tin can
Epoxy Hardener (Component B): 3.56 kg tin can
It should be stored in its original package in a dry environment, protecting from frost.
If appropriate storage conditions are provided, it is 12 months from the production date.