Construction Chemicals
Floor Applications
Ademix 715 Epoxy Tex
Textured Epoxy Floor Coating Material
Ademix 715 Epoxy Tex
Textured Epoxy Floor Coating Material
Description:
It Is An Epoxy Based, Double Component, Solvent-Free, Textured Floor Coating Material Applied by Roller.
Areas of Use:
It is used in concrete and cement screed surfaces, undercoat systems dulled with sand as topcoat, maintenance workshops, garage, and loading ramps, etc, surfaces exposed to normal, medium and heavy loads and chemicals, multistorey and underground car parks and maintenance hangars, industrial warehouses, beverage, and food industry, shopping malls and supermarkets, laboratories, exhibition and fair areas.
Advantages:
It is easy to apply.
It is solvent-free.
It has high mechanical and chemical resistance.
It has a glossy surface finish.
It is orange peel textured and has a non-slip surface.
It has high abrasion strength.
It does not allow bacterial residues, does not produce microbes.
It is resistant to diluted acids, seawater, and soda solutions.
Technical Specifications:
Component A: Epoxy Resin – Color, Liquid (Ral Colors)
Component B: Epoxy Hardener – Transparent Liquid
Mixture Ratio:
Component A: 21,60 kg
Component B: 3,40 kg
Density
Component A: ~ 1,70 kg/lt
Component B: ~ 1,0 kg/lt
Mixture: ~ 1,55 kg/lt
Compressive Strength Mortar: ~ 70 N/mm² (28 days / +23°C / 50% relative humidity)
Flexural Strength Mortar: ~ 30 N/mm² (28 days / +23°C / 50% relative humidity)
Adhesion Strength: > 1.5 N/mm²
Shore D Hardness: ~ 80 (7 days / +23°C / 50% relative humidity)
Abrasion Strength: <70 mg (CS10, 1000, 1000) (8 days 23°C) (EN ISO 5470-1 Taber)
*The above values were obtained as a result of laboratory experiments.
Application Information:
Surface Temperature: +10°C minimum / +30°C maximum
Environmental Temperature: +10°C minimum / +30°C maximum
Surface Humidity Content: Humidity ratio <4% by weight
Full Curing Time: ~ 7 days
Relative Humidity: 80% maximum
Pot Life:
+10°C ~ 80 minutes
+20°C ~ 45 minutes
+30°C ~ 20 minutes
*These values are valid for 23°C and 50% relative humidity. Times may vary depending on ambient conditions.
Surface Preparation:
The concrete surface should be clean, strong and have sufficient compressive strength (minimum 25 N/mm²).
The surface should be clean, dry and free from foreign substances such as dirt, oil, coating, surface curing materials.
Concrete or screed surfaces should be primed or levelled to form a smooth surface.
Mixture Preparation:
Component B of ADEMIX 715 EPOXY TEX should be added into component A and be stirred with an aid of 300-400 rpm for 3 minutes until a homogeneous mixture is obtained.
To make sure that the mixture is made completely, the mixture is put in another container and stirred again for another 1 minute.
Over stirring should be avoided to minimize air entrainment.
Application:
Primer:
ADEMIX EPOXY PRIMER 711/712/713 is applied to the floor with the help of an unused rake or roller.
Surface levelling:
ADEMIX EPOXY PRIMER 711/712/713 products can be used for levelling uneven surfaces.
Coating:
ADEMIX 715 EPOXY TEX is applied with a short pile roller.
Textured roller coating:
ADEMIX 715 EPOXY TEX should be poured on the surface and propagated with a trowel in order to obtain the desired thickness. The textured appearance of the surface should be provided by using a textured (coral) roller.
– ADEMIX 715 EPOXY TEX For the best results in its application, ambient temperature should be between +10°C and +30°C
and necessary measures should be taken in bad weather conditions.
-Processability and curing times vary according to the ambient temperature. The times are shorter at high temperatures, and longer at low temperatures.
-The application area should be protected from heavy weather conditions for 24 hours after the application. (sun, wind, frost, rain, etc.)
– The pre-stored packages to be opened for application should be ready for use at an average of 25°C.
-Upon the completion of the application, the coating should not be exposed to water directly for at least 24 hours.
-Used tools and equipment should be cleaned with cellulosic thinner or suitable solvent after application.
-All application area must be prepared with the same batch number of ADEMIX 714 TEX for exact color matching.
Consumption:
As a coating; for one coat; approximately 0.60 – 0.80 kg/m²
Warnings:
All necessary Occupational Health and Safety measures must be taken in the application areas. All work safety equipment, such as work clothes, protective gloves/goggles /mask, should be used during the application in accordance with the Occupational Health and Safety rules. Ventilation of the working area is required. Warehouse and stock areas should not be approached with fire. Contact of the product with the skin and eyes should be prevented, in such a case, the contacted part of the skin should be washed with plenty of water and medical attention is required immediately. Food and beverages should also not come into contact with the product. It should be kept out of reach of children.
Color:
Component A: Epoxy Resin – Color, Liquid (Ral Colors)
Component B: Epoxy Hardener – Transparent Liquid
Package:
25 kg set
Epoxy Resin (Component A): 21.60 kg tin can
Epoxy Hardener (Component B): 3.40 kg tin can
Shelf life: Storage conditions
It should be stored in its original package in a dry environment, protecting from frost.
If appropriate storage conditions are provided, it is 12 months from the production date.