Ademix Silicone Exterior Facade Grain Coating Paint



Ademix Silicone Exterior Facade Grain Coating Paint




PRODUCT DESCRIPTION:

Styrene Acrylic emulsion based, silicone added, Matt grain exterior paint.

PRODUCT SPECIFICATIONS:

Thanks to the silicone additive, it had high water repellency resistancer.

High water vapor permeability

Moisture and water resistant, high alkali and chemical resistance

It is extremely resistant to the negative effects of the sun’s rays and the salty moisture on the sea shore.

Covering is high.

High quantity

Does not leave brush and roller marks

Does not splash

Does not crack, swell and spill

Different patterns can be obtained if different rolls are used.

AREA OF USAGE:

ADEMİX Silicone Exterior Grain Coating Paint is used on all kinds of exterior, concrete, briquette, gas concrete, plaster, brick, etc. mineral surfaces.

SURFACE PREPARATION:

The application surfaces should be smooth, solid, and capable of carrying the primer and the finishing paint. The surfaces to be painted, all kinds of dirt, dust, loose layers should be cleaned and the necessary surface repair and repair operations should be done.

APPLICATION:

New plaster interior surfaces to be applied for the first time ADEMİX Silicone Exterior Primer should be used. After the primer is applied, depending on the surface, 1 layer is applied with roller and brush..  Topcoat patterning must be completed by scanning from top to bottom with crystal porous coral roll. Since different scans will create pattern differences, this problem would not be possible to remove it by painting. It should be paid attention that the ambient and surface temperature should be between + 5 ° C and + 30 ° C during the application and until the complete drying of the products. It can be applied by brush, roller and spraying.

THINNING AND APPLICATION SPECIFICATIONS :

Thinning rate: 5-35 % with water

Application temperature (° C): 5 – 35

Covering area (m² / lt): 1,5-3 (Single layer) There may be changes in consumption according to the type, absorbency and structure of the application surface.

TECHNICIAL SPECIFICATIONS :

Resin: Styrene acrylic copolymer

Brightness: Matt

Solid content (by weight)%: 65-66

Viscosity (25 ° C-KU): 130-140

Density (20 ° C-gr / cm³): 1.64-1.70

Ph (25 ° C): 8-9

Drying time (at 20 ° C, 65% HR)                         

Touch dry (min): 30 – 60

Waiting time between layers (hours): 4-6

Final drying (hours): 12-20 hours (Depending on the ambient temperature and relative humidity, the drying time may vary.)

STORAGE:

It can be stored for 2 years at 5-35 ° C in its unopened packaging, in a cool and dry place, protected from direct sunlight. Close the packaging cap hermetically sealed immediately after use.

ITEM NUMBER :15.540.1305 RATE NUMBER: 10.300.1010

PACKING INFORMATION:

15 lt (25 kg)

HEALTH AND SAFETY INFORMATION:

HAZARD STATEMENT

H317: It causes allergic skin reactions.

PRECAUTIONARY STATEMENT:

If medical advice is required, keep the packaging or label.

P102: Keep out of reach of children.

Read the label before using.

P261: Avoid breathing dust / fume / gas / mist / vapor / spray.

P280: Wear protective gloves / protective clothing / eye protection / face shield.

P333 + P313: If you show skin irritation or pruritus symptoms : Get medical advice / attention.

P501:  Dispose of contents/ container in accordance with local/ regional/ national/ international regulations.

* Apply to the nearest health institution for unexpected health problems..




PDF İNDİR


İndir (PDF)

Address

İpekyolu üzeri Ökten Sahası No: 277 – Silopi/Şırnak-Turkey
(+90) 486 534 20 73


info@ademix.com.tr

Location





Social media

Follow Our Activity



Open chat