Ademix 7505 Pol Waterproof 2K

Polyurethane Based Two Component Waterproofing Material



Ademix 7505 Pol Waterproof 2K
Polyurethane Based Double Component Waterproofing Material

Description:
It is a polyurethane-based, double component, solvent-free, elastic, crack bridging, waterproofing material.

Areas of Use:
It can be used in water tanks, channels, in wet areas such as bathroom, kitchen, balcony, pools, terraces as waterproofing material.

Advantages:
It is easily applied with a brush or roller.
It does not mix with drinking water.
It has high crack bridging feature.
It has high adherence to the applied surface.
Since it does not contain solvent, it can be easily applied in closed spaces.
It performs over a wide temperature range. Its heat resistance is between -40°C and 90°C.
It is resistant to chemicals, bacteria, and salt solutions.
It is the ideal solution for water tanks in terms of cost-performance.
It is moisture and waterproof.
It is resistant to the freeze-thaw cycle.

Technical Specifications:
Density: 1,30 ± 0,10 gr/ml
Shore A Hardness: 60
Elongation at Break: ≥ 200%
Adhesion to Concrete Strength: ≥ 2 N/mm²

Application Information:
Application Temperature: (+5°C) – (+30°C)
Mixing Ratio: 20 kg Component A / 4 kg Component B
Mixture Usable Time: 30-45 minutes
Time Needed To Walk On is 18-36 hours
Ultimate Curing Time: 7 Days
Average Consumption: 0,600-0,800 kg/m² (for one layer)

*These values are valid for 23°C and 50% relative humidity. Times may vary depending on ambient conditions.

Surface Preparation:

-The surface must be clean and dry, and free from oil, dirt, grease, coatings and other dirt that will prevent adhesion.
-Large fractures and faults must be repaired beforehand.
– Chamfering should be done to corners and joints in the application area.
-The cement crust and glossy screed sanding on the concrete surface should be cleaned with tools such as a notching machine, diamond drum wiping machine, driven grinding, and the surface should be roughened and wiped.
-The entire surface of the industrial vacuum cleaner should be cleaned from dust.
-The surface should be prepared by priming with ADEMIX 7501 POL PRIMER.

Mixture Preparation:
By adding component B on component A, ADEMIX 7503 POL WATERPROOF 2K should be stirred with a 300 – 400 rev/min mixing bit drill for 2 -3 minutes until a homogeneous consistency is obtained.
The components are packed in the correct mixing ratios. If some of the product will be used, this ratio should be considered. Attention should be paid to the consumption of the prepared mixture within the pot life.

Application:
ADEMIX 7505 POL WATERPROOF 2K is applied on the application surface with a notched trowel, brush, roller or airless spray gun.Air bubbles should be removed with a spiked roller within 10 minutes and at least 2 coats should be applied. Wait 12 hours between coats. This period should not exceed 24 hours.

– Since the mixtures will begin to gel in 30 – 45 minutes, the pot life should be considered.

– The weather should not be rainy 24 hours before, during and after application in open spaces.
Avoid application at temperatures below -5˚C and above +30˚C.
– It should not be directly exposed to sun because it has no UV resistance.
-Do not apply on surfaces with negative water pressure.
-All tools and application equipment should be cleaned with thinner immediately after use. Hardened/cured material can only be removed by mechanical methods.

Warnings:
All necessary Occupational Health and Safety measures must be taken in the application areas. All work safety equipment, such as work clothes, protective gloves/goggles /mask, should be used during the application in accordance with the Occupational Health and Safety rules. Ventilation of the working area is required. Warehouse and stock areas should not be approached with fire. Contact of the product with the skin and eyes should be prevented, in such a case, the contacted part of the skin should be washed with plenty of water and medical attention is required immediately. Food and beverages should also not come into contact with the product. It should be kept out of reach of children.

Color:
Blue, White

Package:
24 kg set

Component A: 20 kg tin can
Component B: 4 kg tin can

Shelf life: Storage conditions
It should be stored in its original package in a dry environment, protecting from frost.
If appropriate storage conditions are provided, it is 12 months from the production date.




PDF İNDİR


İndir (PDF)

Address

İpekyolu üzeri Ökten Sahası No: 277 – Silopi/Şırnak-Turkey
(+90) 486 534 20 73


info@ademix.com.tr

Location





Social media

Follow Our Activity