Ready Plasters

Ademix 220

Ready Hand Plaster

Ademix 220
Ready Hand Plaster

Cement Based, Ready Hand Plaster.

Areas of Use:
It can be applied on interior and exterior walls, rough plaster, reinforced concrete, prefabricated wall, brick, pumice and accumulation.

Product Advantages:
Easy to apply.
It adapts easily to the applied surface.
It forms a highly adhesive and durably resistant solid base.
It saves labor and time.
It prevents loss of quality and efficiency that may occur from dosing.
It provides rough and fine plaster function together with a single product.

Technical specifications
Splice Strength: ≥ 0.3 N / mm²
Flexural Strength: ≥ 1 N / mm²
Pressure Strength: ≥ 3 N / mm²
*The above values have been obtained through laboratory tests and are valid for 28 days of the performance.

Mortar Type: G
Dry Bulk Density: 1500 ± 200 kg / m³
Compressive strength: CSII
Bond Strength: ≥ 0.3 N/mm²
Capillary Water Absorption: W0
Water Vapor Permeability Coefficient: ≤ 15
Average Thermal Conductivity: λ10, dry P = 90% ≤ 0.845
Reaction to Fire: A1

Application Information:
Application Temperature : (+5 ° C) – (+35 ° C)
Mixing Ratio: 6.5-7.5 lt water / 35 kg Powder
Application Thickness: 5–20 mm
Consumption Average: 15–18 kg / m² (1 cm for thickness)

*These values are valid for 23°C and 50% relative humidity.

Surface Preparation:
-The application surface should be made clean from dust, dirt, oil, paint residue, and similar foreign matters reducing adherence.
­If there are surface defects (holes and cavities), they should be filled with ADEMIX REPAIR at least 1 day in advance.
­ The surfaces should be moistened with water before the application.

Mixture Preparation:
35 kg ADEMIX 220 READY TO PLASTER is added slowly to 6.5-7.5 lt water. Stirred until a homogeneous mixture is obtained with a trowel or a low-speed mixer, leaving no lumps.

The prepared mixture is applied to the surface and spread by straightening. When the surface starts to harden (in about 4 hours), it should be feathered with circular movements and without pressure with a trowel. For smooth surfaces, wipe with a damp sponge. Wiping should be done immediately after feathering, and the sponge should be cleaned frequently.

ADEMIX 220 READY TO PLASTER The applied surfaces must be moistened within 12-24 hours. The second humidification should be done 24 hours after the second humidification. The surface should be moistened for 2-3 days.

­ It has an application range of 5 –30 mm.For applications thicker than 10 mm, second layer application is started.
­At least 7 days should pass after the plaster application before applying coating, painting etc. on plastered surfaces.
­In order to obtain a smooth surface, the surface must be gauged from bottom to top obliquely.
­At different joints such as walls and columns, window door edges and applications thicker than 7 mm should be used to prevent cracking in thicker applications.
­Should not be applied in temperatures below 5°C.
­Should not be applied to surfaces which are directly exposed to sun and wind without protective measures.
­Foreign materials should never be mixed into the mortar.
­After application, all used tools should be washed with plenty of water before drying.

Do not inhale the product directly, as it is cement-based. Avoid contact with skin and eyes.

Reference Standard:
TS EN 998–1

Packing:35 kg. kraft sack
Shelf life: 12 months in dry environment and in original package


İndir (PDF)


İpekyolu üzeri Ökten Sahası No: 277 – Silopi/Şırnak-Turkey
(+90) 486 534 20 73


Social media

Follow Our Activity